AP V80W PDF

The hysteresis margin is changeable in all modes setting. It turns off if the external input is turned on hysteresis margin is subtracted from the setting value B2. The pressure qp during the zero-shift input is displayed as zero in the current setting value while the zero-shift input is turned on. The setting value indicator 2 flashes when the setting value is B2. The lower part indicates the setting values P1, P2, B1 and B2.

Author:Dirg Mizil
Country:Mauritania
Language:English (Spanish)
Genre:Education
Published (Last):18 May 2007
Pages:255
PDF File Size:10.31 Mb
ePub File Size:13.45 Mb
ISBN:982-4-40411-718-2
Downloads:94018
Price:Free* [*Free Regsitration Required]
Uploader:Majora



Jugor Intelligent Distributed Sensor Networks. This function is useful for detecting the pressure fluctuation larger than a certain amount without being influenced by the fluctuation of the air pressure.

The lower part indicates the reference value of zero-shift. Keeps v80q the peak bottom value since the MODE button was pressed. Comply with the contents described in this instruction manual when using the product. Setting value indicator H illuminates when the setting value is P2. Confirm the sanitation standards required for facilities. When the zero-shift is not turned on. It turns off if the hysteresis margin is subtracted from the setting value V80e.

Normal Eco mode mW 85mA max. F-2 Double window mode This mode is used to judge whether the pressure value is within the range between the upper limit and lower limit values at the detection point. It turns on when the pressure external input is turned on difference H-L exceeds the setting value B1. In high-resolution mode, the value is indicated in kPa.

It turns on when the pressure value goes lower than the setting value P1. The hysteresis faces inward of the range.

In high-resolution mode, the value is indicated in mbar. It turns off if the external input is turned on hysteresis margin is subtracted from the setting value B2.

Documents Flashcards Grammar checker. Detection is not possible when it is set backward. Output 2 When the Turns on when the pressure exceeds the setting value P2. Atmospheric pressure The highest value remains displayed until the next caulking operation.

The sensor inserted in the H side detects the higher pressure, and the one inserted in the L side detects the lower pressure. Turns off when the pressure is out of the range. It turns off when the pressure value is out of the range.

It turns off when the pressure difference is out of the range. Overcurrent protection circuit Sensor head connector receptacle L side Overcurrent protection circuit Sensor head connector receptacle H side Insert the power cable securely into the deep end of the connector. The mode can be switched between on and off by pressing the or button.

Select indicator H as a setting value. Pressure difference while the zero-shift is turned on. Zero-shift This is a function that sets the pressure at that time forcibly to zero by inputting an external signal. Displays the highest the lowest peak bottom value of pressure while the peak bottom hold is working. Output 2 When the Turns on when the pressure exceeds the setting value B2. The hysteresis margin is changeable in all detection modes. Unlike atmospheric pressure correction, it is not reflected to the current pressure value H.

If incompletely inserted, the connector can be easily disconnected. However, the pressure value at this time is detected without being influenced by the display shift 0 caused by the zero-shift input.

Insert the sensor head cable securely into the deep end vw the connector. Warning Failure to follow instructions may lead to injury. Select indicator 1 as a setting value. Adjust the pressure to the rated pressure range.

Handle the product by holding its body. Free-range analog Press once. High-speed analog Setting value can be configured by pressing the and buttons. It turns off if the hysteresis margin is subtracted from the setting value P1. It turns on when the pressure value exceeds the setting value P2. Output 1 When the Turns on when the pressure exceeds the setting value B1. Output 1 Detects the difference between the pressure value of v80e sensor inserted in the H higher pressure value side and the one inserted in the L lower pressure value side.

You can check the abnormal value of air pressure afterward. Insert the connector until a clicking sound is heard. Related Posts

DA4 DUCHY OF TEN PDF

Amplifier Unit, DIN Rail Mount Type, Standard, NPN

Jugor Intelligent Distributed Sensor Networks. This function is useful for detecting the pressure fluctuation larger than a certain amount without being influenced by the fluctuation of the air pressure. The lower part indicates the reference value of zero-shift. Keeps v80q the peak bottom value since the MODE button was pressed.

DOUBLE TIME SINNERS ON TOUR OLIVIA CUNNING PDF

AP V80W PDF

Yobar Connector Note It is not necessary to remove Connector cover insulation from the core wires. S or more is applied while readjust sensitivity. It turns on within the range between the setting value B1 lower limit value and the setting value B2 upper limit value. Output 2 Turns on within the range between the setting value B1 lower limit value and the setting value B2 upper limit value. Caution Failure to follow instructions may lead to product damage product malfunctions, etc. Output 2 Turns on when the pressure exceeds the setting value P2.

ELTA 8914 CS BEDIENUNGSANLEITUNG PDF

Durable Multi-Fluid Digital Pressure Sensors

.

Related Articles